john555 0 Posted September 18, 2009 Report Share Posted September 18, 2009 ok iv just been looking at the bits of my kit on the floor and iv realised either im sum bits missing or im doing somethong wrong, does anyone have any instructions or detailed photos of there instalation, or can anyone even tell me which bits go were here a few pics of the bits i have im more just stuckon were the pullys go than anything elseis this the correct order for these bit or am i missing any bits or incorrect orderwhat are all these bolts for or are they just random bits Link to post Share on other sites
craggsy 91 Posted September 18, 2009 Report Share Posted September 18, 2009 Picture 2: charger is upside down. I'll pop my pics up that i did whilst putting mine in Link to post Share on other sites
craggsy 91 Posted September 18, 2009 Report Share Posted September 18, 2009 Bottom pic is a guide pin that screws into the head and then the hole between the 2 raised bits goes on to it. Lines it up so you can bolt it up thro raised bits holes. If you get what I mean Link to post Share on other sites
craggsy 91 Posted September 18, 2009 Report Share Posted September 18, 2009 Thats how it looks all put together Link to post Share on other sites
craggsy 91 Posted September 18, 2009 Report Share Posted September 18, 2009 That pin in your last pic Link to post Share on other sites
craggsy 91 Posted September 18, 2009 Report Share Posted September 18, 2009 Any other help and i'll take a few more pics for ya. Do have others but not best ones Link to post Share on other sites
john555 0 Posted September 18, 2009 Author Report Share Posted September 18, 2009 thats perfect ill have another shot and see what i can come up with thanks i owe you onejohn Link to post Share on other sites
john555 0 Posted September 18, 2009 Author Report Share Posted September 18, 2009 ok im confused again why is my charger pointing up when the oil in and out lets are in the same place as yours can the housings be rotatedi get what you mean about the pin now like this Link to post Share on other sites
craggsy 91 Posted September 18, 2009 Report Share Posted September 18, 2009 Youve got it. Housing can be spun round. There is a PDF I think on the rotrex website. Or give Storm a call tomorrow asking how to do it Link to post Share on other sites
craggsy 91 Posted September 18, 2009 Report Share Posted September 18, 2009 http://www.rotrex.com/pdfs/Rotrex_Technical_Datasheet_C30_Range_V4.0.pdfHere ya go Link to post Share on other sites
john555 0 Posted September 19, 2009 Author Report Share Posted September 19, 2009 cheers thats spot on iv think the kit iv bought is a bit poor to be onist nothing fits properly so going to have to get a few bits remade wish id just bought a new kit now Link to post Share on other sites
RIX 0 Posted September 21, 2009 Report Share Posted September 21, 2009 also missing a pully as far as i can see,plus you pully from the tensinor must be reused Link to post Share on other sites
john555 0 Posted September 21, 2009 Author Report Share Posted September 21, 2009 lol yer iv done a swap with my 22psi pully for bobbys 18psi one just waiting to get his back after he gets his car mapped as for the tensioner pully i have two alloy ones so shouldnt need to reuse my tensioner one, im only realy missing the sections that mount the idler pullys to the tensioner and bracketcheers john Link to post Share on other sites
john555 0 Posted September 25, 2009 Author Report Share Posted September 25, 2009 ok well iv managed to make all the bits i was missinga lh bolt to screw into the tensioner and all the idler spacesthanks for all the help cheers john Link to post Share on other sites
Recommended Posts