joeboy 1 Posted January 1, 2012 Report Share Posted January 1, 2012 I've been recently indulging in some carbon fibre wrapping. I started off doing some on my own car, then a few mates said it looks good and they would like some down too and it's gone on from there. Have a look at my Facebook page and tell me what u think.Facebook/tidywraps Link to post Share on other sites
oldmandon 1 Posted January 1, 2012 Report Share Posted January 1, 2012 VERY nice work, how much do things like that cost to get done?? Link to post Share on other sites
joeboy 1 Posted January 1, 2012 Author Report Share Posted January 1, 2012 Well I haven't been doin it long, it start from a fiver which would be the the the door handles the door handle surrounds and around air vents. And about £30 for a centre dash like in the picture of the 206. Link to post Share on other sites
oldmandon 1 Posted January 1, 2012 Report Share Posted January 1, 2012 Be interested in both door handles, the surround by the sunroof and the centre panel in the dash. how much and how would you go about doing this? Link to post Share on other sites
joeboy 1 Posted January 1, 2012 Author Report Share Posted January 1, 2012 The centre dash do mean the same as in the picture of my VR just around the heater controls. Link to post Share on other sites
oldmandon 1 Posted January 1, 2012 Report Share Posted January 1, 2012 yep pretty much..... Link to post Share on other sites
joeboy 1 Posted January 1, 2012 Author Report Share Posted January 1, 2012 It would be £40. The only way I would be able to do it was if u sent the parts to me because its a bit of a trek to south Wales and i only do this as as side job. I would send them bk for free. Link to post Share on other sites
bungy 2 Posted January 1, 2012 Report Share Posted January 1, 2012 Do it yourself Don it is nice and easy. I did my handles and other bits and pieces.from this to thisfor only a couple of quid and some time and patience Link to post Share on other sites
joeboy 1 Posted January 1, 2012 Author Report Share Posted January 1, 2012 I agree it is easy with a bit of patience and some heat. Link to post Share on other sites
bungy 2 Posted January 1, 2012 Report Share Posted January 1, 2012 Also make sure you degrease whatever it is you are sticking to. Link to post Share on other sites
oldmandon 1 Posted January 1, 2012 Report Share Posted January 1, 2012 Ok, so if I try this myself, what equipment do I need to buy and what type of vinyl do I need.....Also what do you use to degrease the items with?? Link to post Share on other sites
joeboy 1 Posted January 1, 2012 Author Report Share Posted January 1, 2012 You can get the black carbon fibre wrap form eBay, a sharp knife e.g scalpel, craft knife. A heat gun or a hair dryer will work. And to clean the pieces I use white spirit or methylated spirit with industrial blue paper towels. If u get stuck there's lots of videos on YouTube to help you out. Link to post Share on other sites
bungy 2 Posted January 2, 2012 Report Share Posted January 2, 2012 Have a look at my build thread Don, I yhink I posted it all on their before. Link to post Share on other sites
oldmandon 1 Posted January 2, 2012 Report Share Posted January 2, 2012 Have a look at my build thread Don' date=' I yhink I posted it all on their before.[/quote']Come on...I'm lazy where's the link??!! lol Link to post Share on other sites
bungy 2 Posted January 3, 2012 Report Share Posted January 3, 2012 Have a look at my build thread Don' date=' I yhink I posted it all on their before.[/quote']Come on...I'm lazy where's the link??!! lolCome on lazy bones..... Link to post Share on other sites
Recommended Posts