ssaunders 199 Posted October 29, 2013 Report Share Posted October 29, 2013 Hi just need conformation on the above. i am fitting a schrick soon and wanted to replace the schrick to lower manifold bolts i have been led to believe these are M8 X 30 mm.all help appreciated.cheerssteve Link to post Share on other sites
michael5556 247 Posted October 29, 2013 Report Share Posted October 29, 2013 M8 is correct. And 30 sounds about right but don't quote me on that Link to post Share on other sites
Lukey. 381 Posted October 29, 2013 Report Share Posted October 29, 2013 yes they are Link to post Share on other sites
ssaunders 199 Posted October 30, 2013 Author Report Share Posted October 30, 2013 thanks guys! Link to post Share on other sites
VR6Pete 1,455 Posted October 30, 2013 Report Share Posted October 30, 2013 Yep they not cheap from VW lol Club Chairman Link to post Share on other sites
Lukey. 381 Posted October 31, 2013 Report Share Posted October 31, 2013 Just get some nice stainless ones, they aren't tightened to a huge torque VR6Pete 1 Link to post Share on other sites
ssaunders 199 Posted November 11, 2013 Author Report Share Posted November 11, 2013 Just get some nice stainless ones, they aren't tightened to a huge torque done! Ebay about 4 pounds for 10 stainless and split washers (if needed)thx GuysS Link to post Share on other sites
paceo 22 Posted November 11, 2013 Report Share Posted November 11, 2013 is yours obd1? need to find out how to wire mine up! Link to post Share on other sites
ssaunders 199 Posted November 15, 2013 Author Report Share Posted November 15, 2013 ok, next question!. whats the size of bolt from lower to upper? they are too small to be M8, how can i tell what it is if i take one out? from upper to TB mount are M8 but shorter i will get some 25's if there is such thing.thanks again all.steve Link to post Share on other sites
Lukey. 381 Posted November 15, 2013 Report Share Posted November 15, 2013 Are you sure? I was certain they are the same size? Link to post Share on other sites
ssaunders 199 Posted November 15, 2013 Author Report Share Posted November 15, 2013 Hi, here is pic, on left is M8x30, middle is lower to upper and right is TB to to mani. It's the same width as TB to mani but only 20 mm.CheersSteve Link to post Share on other sites
Lukey. 381 Posted November 15, 2013 Report Share Posted November 15, 2013 Sorry run a total blank on them. They look M4 or M6 Link to post Share on other sites
Lukey. 381 Posted November 15, 2013 Report Share Posted November 15, 2013 I looked in etka as I was sure mine were the same size, and etka says they are too, however, if yours are different and are the same size as the throttle body bolts, the TB bolts are M6. Link to post Share on other sites
ssaunders 199 Posted November 15, 2013 Author Report Share Posted November 15, 2013 Thank The Lord for Lukey and Etka!It's for a schrick if Etka covers those?Thx again mate.Steve Link to post Share on other sites
Lukey. 381 Posted November 15, 2013 Report Share Posted November 15, 2013 No it doesn't lol VR6Pete 1 Link to post Share on other sites
VR6Pete 1,455 Posted November 16, 2013 Report Share Posted November 16, 2013 is yours obd1? need to find out how to wire mine up!What are you trying to wire up?Club Chairman Link to post Share on other sites
Recommended Posts