Leaderboard

Your Passat is twin engined?! Wtf? [emoji23]

That's rite sqeals 4.7 litre 10 cylinder pissrat lol part diesel part petrol

Back on car. Got it all built back up, and sitting how I wanted Pics to come soon While I had the inlet manifold off, I opened up and re-shaped the inside of the neck near the throttle body. I then drilled out and fitted a 1.8T temp sensor. As there meant to not get heat soak, and also work much better with forced induction. I also drilled out and changed the vacuum fitting. but didn't get pic after finishing the vacuum fitting. Before re-fitting it on car, removed the sensors, an gave it a good very good hot wash, degrease, light acid wash, neutralise wash, then clean hot wash again. to

That install looks dodgy to me....... Lol

Another vr6 I'm buying off a mate, it's in very good condition floor is solid and it has a tiny rust hole the size of a 10p on one of the sills, the black one will be stripped and most of the stuff will go onto the new one.

Ah, hybrid technology, good work! [emoji87]

Back to the suspension and how the car sat..... after getting the customised lower arms, ball joints, and new custom suspension back on, and testing how low the car sat. I still wasn't happy, the car still needed to sit a tiny bit lower, maybe more if possible. but the lower arms still bound on the subframe too early for my liking, and i wanted it sat lower! So there was only two routes I could take, as I've already done alot to make it sit lower. 1. ball joint raiser, or 2. raised turrets. Normal ball joint raisers / extensions don't fit and work with VR6 ball joints, meaning i would of had

Yeah it has an extra sealer, and last longer lol

Haven't found time to do an update in awhile, been flat out working on the car in my spare time, kinda why there been no update, as I've been to busy doing stuff to it. Finished heat wrapping my exhaust, I did the down pipe ages ago, but never did the headers, as previously i did it while the whole engine was built up. So got round to heat wrapping the headers. I also heat wrapped the under side or my inlet manifold, With this special ceramic heat shielding. It's called Zircotec. I went for ZircoFlex 3. This is there website on the stuff: http://www.zircotec.com/page/--zircoflex-iii/150 Th

It did have an extra 12v in it untill it got dropped off at my house. Thanks again by the way

hi mate, the wire is probably to the siren (if it has one) and there would also be a bonnet trigger (little plunger on front panel) for the alarm as well. i have found this link that has the wiring diagram http://www.escortevolution.co.uk/forums/topic/96661-cobra-3190-wiring/ what numbers are the red and white wires hiding? 3?9? from the diagram the green wire on the mono block looks like its the engine stop you will need to bridge this possibly to the 12V in. I'm sorry im not an alarm fitter ;-) the only other way will be to follow the monoblock wires to the original loom and reinstate. appar

hi mate, whats the model of the alarm? i will have a look round for you. do you have the PIN code for it? s

Dodo juice is amazing, I've used it on mine for last 2-3 years. They also make a purple haze pro, Blue velvet will also work well on your colour car, And smells even better than purple haze.

Come on folks, been attending a few shows this year and must admit the support from the VR6OC has been a bit Grim. Lets put ourselves back out there as one of the big guns when it comes to the shows!

I think I've came to the wrong forum lol Davey my mate who's does remaps is Paul, tell him Matty sent ya, I think it will be his first vr mapping as well but could be wrong http://www.unit9remaps.co.uk that's his site mate

Hi, it´s not possible to run pistons für Chargers without one. The comp would be too low to let the engine work well. Drive stock pistons till you upgrade.

If you fancy coming along and representing your club and want to put your motor on the stand shout up. I've now started the list at the top of the page. Thanks

Got a nice big Holset turbo on its way!

It's alive! https://vimeo.com/127356810 Another box ticked on my bucket list.......own a supercharged car![emoji16][emoji1] Love that noise!

Anyone going to this It's in a week from Saturday 16-17th may.

Photo of my new bungs and new head shield fasteners, got loads more bungs, but couldn't be arsed to line them all up for photo, lol New front struts / dampers arrived , I'm making some extra low front shafts to mount my bags on to I'm only using the front pair. so rear pair are for sale, brand new in the box if anyone want them. The mounts on the bottom are removable and adjustable. Tiny bit of customizing, then got them in to zinc primer, then in the polyurethane top coat. Shafts with mounts ready set up for air bags, bronze colour is copper grease. All built back up read