Leaderboard
Popular Content
Showing content with the highest reputation on 08/31/2015 in Posts
-
I will be, as long as this weather hasn't turned the place into a bog! But only for the Sunday, in the VR of course[emoji106]3 points
-
not noticed before that you in newcastle will have to keep my eyes peeled for you!2 points
-
I managed to get a door in the back of a 3 door corsa with the rear seats down.2 points
-
Ok. So sump has gone to @dlea to weld the AN fitting [emoji106]2 points
-
Hello from essex UK :) new member , first vr6 build
redvr6_girl and one other reacted to VR6CABBS for a topic
In all fairness there's not a lot that can go wrong Kell. Apart from the paint cracking but plenty of heat should do the trick. There loads of videos on u-tube as well. And some funny ones. Rolling them with a baseball bat. Haha2 points -
Put me down for this one Dave....2 points
-
Been invited to have host a club stand here. A single day event on Sunday 18th October. I know the lads hosting this and they really do a great day. Plenty of family orientated things going on. Rides for the kiddies and that. They are a really good crowd tbh. Can just do a small stand 5 cars or so however more would be great...! So come on show me some interest, Lee I know its your area don't be shy hahaha Chris you to! There is also going to be a Rolling Road there on the day for power runs, some drifting also the runway will still be live so plane spotters or wanna be terrorists ca1 point
-
Edition 38 this weekend!
bennyk reacted to rhysemerson7 for a topic
Who's there?? What you taking? Mk5 r32 is out on a trip with me!!1 point -
1 point
-
Brilliant mate! Needs to get one of those rat roof boxes on the go then Hahaha!1 point
-
Have you seen in the boot of that bealieboys car?? It's rigged out with a big humper thumper bass pig and the usual emergency kit for when the misses kicks him out. Hahahaha. All its short of is a kitchen sink. [emoji23][emoji23][emoji23]1 point
-
There was actually a set on eBay a little while ago, I brought them :)1 point
-
youll have to look hard. It's bad enough trying to find him at a show! He is the lesser spotted Dave![emoji23]1 point
-
Dave, there'll be less chance of you getting that in a 3 door than me getting it in the 5 door![emoji23]1 point
-
Sounds good to me...1 point
-
Awesome I will bring that door HAHAHA1 point
-
Edition 38 this weekend!
rhysemerson7 reacted to VR6CABBS for a topic
I'll be there but only on Sunday and not bringing the VR.1 point -
I might be into this one Dave1 point
-
I have one you can buy cheap and I'm in Newcastle1 point
-
Right so i am waiting for my misses brother to come down for a weekend and show me how to weld because i am stuck right now I cant do much until the welding is done. Back to the engine it turns out the sqeek coming from the supercharger was not bad berinngs it was pressure not able to escape when throttle was closed so it was forcing the screws to strain my initial reaction was to move the throttle before the charger but i have decided against because i dont want a surge of remaining presure when I close the throttle, so I have left the throttle in its original location and got a blow of val1 point
-
16 x 9 Schmidt modern line wheels, lowering and camber!
Bealieboy reacted to reynolds9000 for a topic
forgot to add that the front and rear arches are completely rolled flat and front camber is at full negative. I never measured in degrees, I just loosened the strut at the steering knuckle and pushed all the way in and tightened it all back down. set the toe based on my eyeballs and my fenders and got pretty decent tire wear and fairly good tracking given the negative camber.1 point -
16 x 9 Schmidt modern line wheels, lowering and camber!
Bealieboy reacted to reynolds9000 for a topic
when I had ML's.. I miss them. specs were 16x9 all around, ET25 front and ET15 rear. I used 205/40/16 Falken 512's which are NLA.1 point -
I've a keen eye for stuff like this! [emoji23]1 point
-
No you couldn't of done Bealieboy would of sent me a link[emoji15][emoji16] he definitely would've found them!1 point
-
Been busy this last week with the car, first I got the Eurospec 280mm rear discs that were on the black VR I broke machined as they were quite badly corroded after sitting on that car going nowhere for a couple of years, luckily the car had done hardly any miles with them fitted so they had loads of meat left on them, this was before fitted the black Golf; Discs after being machined by a local machine shop; Next to the standard size disc; Removing the caliper spacer bracket from the old axle, needed a bit of heat to get them off; Old discs and heat shields removed; Then all back together; Th1 point
-
Hello from essex UK :) new member , first vr6 build
VR6CABBS reacted to redvr6_girl for a topic
Will let you know going to use a heat gun so to try not to crack the paint [emoji58] if not I have someone on stand by to repair it if it goes Pete tong [emoji41][emoji41]1 point -
Ooo, I'd be interested in how you get on with that! [emoji41]1 point