Jump to content

drummie

Members
 View Profile  See their activity

  • Content Count

    13

  • Joined

  • Last visited

 Content Type 

Everything posted by drummie

  1. drummie
    Anything I should be aware of? Its done 20K I've owned 2 Vr6's so I know a lot about the engines etc. Are there any major issues with the R32's ? Thx for any info. Dave.
  2. drummie
    Oh dear no. I got someone to do all that stuff already. Bottom-end reconned fully, new rings and shells. No regrind of crank needed! And head done, new valve stem seals etc Now just need it rebuilding properly. Enjoyed taking it to bits but that's as far as my tiny skill level could go. Thx for info, rung headshop but guy was out on a job and not rung me back yet. Will try em again mon. Cheers Dave.
  3. drummie
    for the record. average over the last 3500miles 27.8 and I drive pretty quick most the time. Hard/round town trip never less than 22mpg and driving at best 48mpg!! I had this last week on the motorway while driving through traffic at steady 55ish. Stayed around that mark for miles. Does bout 39-40mpg in 5th at 30 mph. I'm sure this is incorrect. Spec of my car. 97 Highline, chipped, decat, BMC filter, Ashley 6-2-1 manifold, 15" BBS's, pretty much always use shell v-power. seems to give the best Mpg. Have certainly noticed that the "lame" driving speed mpg has gone through the roof since the d
  4. drummie
    Thx!
  5. drummie
    I had an ashley 6-2-1 manifold fitted earlier this year and had had my old crappy 6-2-1 manifold off several times to be rewelded. But, the problem came when putting the new manifold on because, as mentioned above, the exhaust stubs on the head kept breaking when being tightened up. What should have been 4 hours, took 9. Hope this is of some help. D.
  6. drummie
    Hi there. I've modified this post as I should explain I know very little about cars etc. And although this question may appear stupid, I really don't know how to do this but for somwething so simple, i'd rather learn than pay someone and get charged through the nose for it!! All I want to do is get a wire from the engine bay in to the car and apparently I can do this via the clutch cable through the bulk head... Is this correct ? ... because I can't see a way through. any thoughts would be great. btw, it's a MRk 3 golf Vr6. cheers dave
  7. drummie
    Thx for the replays. I'm in Sale south manc. Yes, I just need the engine rebuilding. Have all the bits except the timing chain kit and a few new bits to replace like clutch and flywheel etc. And then just gonna get it fitted. Cheers. Dave
  8. drummie
    Hi there. Been a member here for a year or so but am pretty quiet. just read stuff mostly because I don't know much. But i've got a question that maybe someone can help me with. I have a reconditioned VR6 engine that is totally in bits. I had the head and bottom end done earlier this year and was gonna get the engine put in my car but i need someone to rebuild the engine for me. I was going to do it myself as I took it to bits but with serious lack of time and an even more serious lack of knowledge(!) i'm trying to find someone who would come recommended to do this work, then i will get my us
  9. drummie
    Hi there. Been a member here for a year or so but am pretty quiet. just read stuff mostly because I don't know much. But i've got a question that maybe someone can help me with. I have a reconditioned VR6 engine that is totally in bits. I had the head and bottom end done earlier this year and was gonna get the engine put in my car but i need someone to rebuild the engine for me. I was going to do it myself as I took it to bits but with serious lack of time and an even more serious lack of knowledge(!) i'm trying to find someone who would come recommended to do this work, then i will get my us
  10. drummie
    Oh great. Thx for you help. Someone off VR6.org also said the same thing today. I didn't realise that the "n"reg model was OBD-2. Can go ahead with recon now. phew. thx. Dave.
  11. drummie
    Hi there. I'm no expert, as you'll gather (haha) and I'll try to be as clear as possible. I own a P-reg Golf VR6 Hignline. I have just bought, as a project for myself, an N-reg Golf VR6 Highline engine. Done about 90K. All running fine except value seal leaking on #5. I've stripped it down as far as head off and bout to take off the crank etc. My plan was to recon the bottom and top half, and then do a swap over in to my 1997. Now, i was reading that there are differences between the OBD-1 and OBD-2 and here is my question. Can I not put this engine in my 1997? Or will it be ok. What are the d
×
×
  • Create New...