Jump to content

rodney

Members
 View Profile  See their activity

  • Content Count

    2,747

  • Joined

  • Last visited

  • Days Won

    1

 Content Type 

Everything posted by rodney

  1. rodney
    I got my cat from Longlife Stainless exhausts (see earlier in this thread). Give 'em a call. Made to order and has a lifetime G on it.. In the area of £200 - £250 fitted....
  2. rodney
    Welllllll. I (the Phirm) have had fitted the 13 Bar Oil Cooler.... So here are some pointer for y'all Right well you can get the kits from 3 main sources. Stealth Phirm Mocal DIrect. The kit is in the region of £160 + Fitting. If it's being good then litterally an hour if not allow a day... Access from the underside really is a must to be honest. They are really quite easy to fit with a large HOWEVER! What you are doing is removing the standard oil cooler which runs of the coolant water and replacing it with a nice new little radiator/cooler. There are a few places to physically locate i
  3. rodney
    Sorry to teach you to suck eggs.....Not my intention Sometimes they need to settle but that should not be tooo noticable and tracking can alter the view but again not by that much.. Just check your measurements with the wheel off to a common point like Hub Centre and ensure you have the same measurements. When you say springs aleady fitted to the shocks do you mean they are an all in one deal or seperates ? As all in one would make them coilovers in which case sorted.... Just adjust them....
  4. rodney
    was the engine cold?????
  5. rodney
    Ok, So basically you loose pressure in the pipe and thus will loose some torque low down... Some basics for all exhausts. ..... There is a balance between flow and an amount of pressure required. Varies from car to car and engine type to engine type. If you take a pea shooter zorst off then the car can breath more easilly. You get better performance higher up but poorer lower down.. It's a trade off! If you're wanting to do the whole thing correctly. Spend the money on a made to measure where you can manipulate the profile as you need. The manifold in a standard VR6 is pretty good as
  6. rodney
    well I think it was a good game and you guys played well and looking good for future matches! The ref had a ruff match both sides... I saw the replays and they were on side earlier. That said the Ref must have had a bet on for that final challenge/free kick....
  7. rodney
    What he said..... Sorry should have been a bit clearer..... & Thanks ... Let us know how it goes... Hope that helps..
  8. rodney
    Like said at the top just missing boxes.....
  9. rodney
    looking good there.... Keep the pics coming....
  10. rodney
    really interseted to see if there are OK as replacement ones are a right load of sheckkles normally.....
  11. rodney
    Well there are the ususal things to check.... Does it only happen under load or when you rev it??? I ask so you can pop out a plug or a lead and see what effect is has when testing!!!!!!! Are all the contacts clean and where applicable gapped correctly? (Spark Plugs/throttle boddies/MAF etc etc etc etc) Are all HT aspects ok? Coil pack and cables???? Is the Alternator working correctly????? Is the battery good????? Are the ECU contacts etc all clean and not wet etc etc etc Do you have any fault codes such as Lamba sensor?????? After that we will need to look a little deeper..... such as mo
  12. rodney
    Is Lime a Posh Green colour???? Also is it just the way the picture has been taken or has one connector only cot one wire connected to it???? ( AH just read above) What happened to the refernce VR6 that was on in the main thread???? I don't know that one I am afraid...
  13. rodney
    I came a cross this Real or Fake...????????? http://www.worldcarfans.com/6070313.001/1
  14. rodney
    Sparkz will be impressed with the Colour me thinks...
  15. rodney
    Dude did you know your steering wheel is on the wrong side ....... I think they look cool. Like said above. What you got on the build of the oily bits??????
  16. rodney
    don't use your right foot is the only way to save fuel mate
  17. rodney
    I was on another chat room and as you wander down the list of discussions, if you paused over the thread title it gave you the first I dunno 6 lines of the original tread entry in a little window bubble I found it useful when looking at similar headings and threads if you see what I mean.... So I didn't have to open each one... What do ya' think????
  18. rodney
    check your levels first of all then if that's not an issue you will need to look at the adjustment just to see if stuff is worn........
  19. rodney
    where is the noise???? Did you fill it back up and where was it draining from???? MAin water pump at bottom on Drivers side out of sight. Aux at rear on passanger side and fans at the front. Let us know
  20. rodney
    Blimey! well done to the team.....
  21. rodney
    go stand alone on the ECU....
  22. rodney
    Well done I would have gone for the black to make the shine ... well shine if you see what I mean
  23. rodney

    Haloween!

    rodney replied to blondie's topic in General Chat

    Just wiring my gate up to a battery.... Trick or treat MMmmmwwwwwwwwaaaaaaaaaahhhhhaaaaa.... (sinister laughing sound!!!!!!)
  24. rodney
    AAA engine number is 2.8 I think from memory
  25. rodney
    My MPG improved until I use the right foot. I get a good 34 on the motorway at motorway speeds. Around town if driving normally I still get better than 22mpg. If using right foot around town lots I can get single figures quite easily. Likie the guys say it's all about the right foot usage. How much self restraint do you have
×
×
  • Create New...