Jump to content

f4rrs

Members
 View Profile  See their activity

  • Content Count

    21

  • Joined

  • Last visited

 Content Type 

Everything posted by f4rrs

  1. f4rrs
    My oil pressure switches were changed yesterday as they were both leaking oil. The garage has i used has made a mistake and replaced both switched with two black tops. After much research i know understand that you should have one black top and one brown top. My question is the right or left switch the brown one? Many thanks in advance....... Paul
  2. f4rrs
    Hi, i have 95 VR6 OBD1 and have lots of problems starting my car. It turns over but can take up to 2 to 3 mins to catch. On a couple of ocassions the battery has gone flat before it has started. I have replaced the battery within the last two weeks and the car has just been serviced with new plugs and oil etc and it hasn't improved at all. Has anyone had this problem before? Your help would be appreciated
  3. f4rrs
    Thanks for your help
  4. f4rrs
    Hi, Does anyone know the pressure settings for standard rims on my 95 golf VR6..... Many Thanks
  5. f4rrs
    Hi, Also attempting a change on Sunday. Whats size nut is the filter housing nut? 32mm or 36mm Cheers Paul
  6. f4rrs
    Its a project and just can't justify £27.00 on a new one
  7. f4rrs
    I was going to try that tonite... How much did you use and how did it come out? Cheers
  8. f4rrs
    Yes mate it was off the car. Ive tried the brush but just can't round all of the tank. A pal of mine has suggested caustic soda but that seems a bit too strong.....
  9. f4rrs
    Hi There, I have a really dirty header tank. I have flushed it through but can't get my hand in there enough to clean it all. Has anyone tried to clean there's with any success. I've tried bleach with no effect... Any tips???/ Cheers Paul
  10. f4rrs
    Need to remove my drivers side wing. where are the bolts to do this?
  11. f4rrs
    Hi Guys, Just another question. The wires all seem to end up in a connector plug at the chasis side. How do these disconnect for removal? Many Thanks
  12. f4rrs
    Hi guys/girls, I have a leeky sunroof seal that i need to replace as it lets in water.... Has anyone changed their seal and how easy is it to do? Thanks in advance
  13. f4rrs
    Hi, I have a rusty door that i would like to remove from my 3 door 95 VR6. The questions are: What needs to be removed before gaining access to the hinges? Do you need to remove the bumper and front wing? If so where are the mountings for the front bumper? Looking at the front wing the top part looks easy to remove but how do you remove the bottom bit? Many Thanks in advance Paul
  14. f4rrs
    Hi, My car is booked in this weekend as it needs some welding to the floorplan for its MOT. My problem is that ineed to remove the interior carpet just behind the drivers seat. There is an overlap piece of carpet in the rear footwell corner (3 door) witth a black cap which is about 2cm wide that i need to remove. How do you remove this cap without breaking it? I've tried turning it and levering it up but i must be doing someting wrong...... Your help would be greatly recieved.. Cheers Paul
  15. f4rrs
    Hi, Planning to change my coolent this weekend as looks like it hasn't been changed for years. Had a quick look under the bonnet and the bottom red hose looks like a real bugger to get to from underneath. Is it as hard as it looks or is there an alternative raining point that i have missed. Your tips ewill be greatly recieved Cheers Paul
  16. f4rrs
    Hiya, Theres loads of mud and crud in the my front door speaker grill and would like to remove it to be cleaned. Had a quick look last night in the dark and couldn't work out how it comes out. Your advice will be greatly appreciated. Paul
  17. f4rrs
    Hiya, Theres loads of mud and crud in the my front door speaker grill and would like to remove it to be cleaned. Had a quick look last night in the dark and couldn't work out how it comes out. Your advice will be greatly appreciated. Paul
  18. f4rrs
    Hi, My project 3 door vr6 has had the side sill cover removed before i bought it. Meeting somenoe at the weekend who is breaking a vr6. My question is how do you remove these sills? R they just clipped on? If so has anyone removed these before and is there a knack? Cheers Paul
×
×
  • Create New...