ibiza vr6
-
Content Count
44 -
Joined
-
Last visited
Content Type
VR6OC News
Website Content
Profiles
Forums
Calendar
Gallery
Store
Collections
Community Map
Everything posted by ibiza vr6
-
hi iv striped my 2.8 vr6 again every time itime it up and turn it round once its not lined up with the tit on the presure plate is there a beter way off doing this ? as when i ran it last time it sparks on number 1 lead but makes no diffrents to the running is this y ?
-
as some mite no i have a 2.8 ibiza would a 2.9 fit with my loom my ecu is not chipped to car so would a 2.9 fit and is there much diffrents and any one no were i can get ether a 2.8 or 2.9
-
hi not long ago my head went so i had it skimmed and put it back on again it ran lumpy so i checked timing it run fine and has very good power but ticks over at around 500 revs and every now and again slight popfrom air filter all so has a nosiey tapping from lifter witch will soon go i could do with a set off lifters and gaskets for inlet and exhaust seems hard to get these days any idears
-
will do amate here dose chipping and remaps ect looking him up bellautos from york http://www.bellautoservices.co.uk/
-
at the end off the day its only a car if it gose wrong scrap it and get some thing else you get 3 months garantee and as far as fitting been in trade will sort some thing and its down to fit my car and a manifold is only 90 on ebay
-
will do iv read a bit about them dont seem the worst going if nothing ill get the kit so only need a good turbo
-
will do mate it mite be pants lol but worth a go for that coin
-
why have i heard u can pull 400 bhp before damage and iv upgraded head gasket and done chains and tenstioners im in trade and a few mates that do stuff like this and say it would be fine as long as u dont try and put to much through ?
-
yea depends on how u driv if your heavy right footed all the time then it wont last i want it for 1/4 mile runs and i lttle fun £700 is cheap and can soon upgrade turbo
-
seen one for 700 for full kit may be not the best but cheat to start dont get me wrong its fast as it is but a bit more wont hurt lol
-
yea sorry it is so turbo is cheapest option then lol
-
Stage 2 Supercharger Kit (8psi) 280bhp Replacement charger pulley for increased boost Stage 2 high capacity Bosch fuel injectors Replacement serpentine belt VF race bypass valve Stage 2 chip Upgrade from Stage £700 is this cheap its from TSR PERFORMANCE
-
any idears off prices ? and dose it make a noticeable diffrants
-
hi dose any one no any thing about super charger iv been reading a bit i take it u just bolt them on and go ? do they just air in the faster u go the more air they suck ? and last where is the best place to find on second hand ???? thanks for the help peeps
-
dose any one have numbers or email address for gaskets i want both inlets and exhaust rocker and if cheap enough 12 lifters unless some one has some or if any one is local to york i could do with a timing tool for cams
-
hi dose any one noe off a web site to get turbo stuff for my vr6
-
thanks for the help in the end it was leads when it boiled they must of fooked up got some today 45 it runs mint at last its took long enough lol just need to sell it now
-
unpluged air flow made no diffrents at all dose that sound fooked ? and any one got one near york or at least to try ?
-
been reading on hear people have had probs with lumpy running then when accelerating its grate mines doing that could it be maf its only lumpy when i first set off for a second and if i rev up first its fine very responsive down the road i may be thought leads ?
-
got my vr6 done running did timing like some said now its a little lumpy at stand still as soon as i set off its grate full power every thing then some times it ticks over grate just as i set off for a slit second its lumpy and idears may be plug leads ill try any thing
-
hi got my ibiza vr6 running fine now it warms up to nearl 3/4s off the way i took stat out fan on all the time and went out it did it again now iv flushed it through not been out as yet could off been an air block ????
-
thanks for your help mate was a tooth out must off moved when removeing cam sproket
-
dose any one no how to set timing marks top and bottom with out taking engine out is it TDC and one witch piston ? help please feel strest dropped spanner into sump so that to take out now
-
hi just done head gasket on my 2.8 vr6 and got it running it was hard it get running been down road in it and its lumpy after 3000 rpm and when reving any thing i could i off left some thing off ????
-
hi dose any one no if it is posable to do an head gasket with the engine still in the car iv looked and it looks like it if so please let me no just to make sure thankes andy